7
This auv is designed to map seafloors down to 2500M depth. It has a 1.4kW lithium ion battery pack
with onboard solar charging. It has a sass sonar, forward looking sonar, and side scan sonar. With
four fins it is able to easily maneuver and navigate many types of water bodies.
This hardware wallet can generate key and address pairs and sign transactions. A neat feature that is
being explored is key trading. In many credit card systems there is a pre-authorization
and the transaction is saved on the POS. Then later possibly daily the POS sends up the pre-auths with
the actual amounts etc. This key trading would be like an offline pre-auth but there would be a
physical transfer of the key using an encrypted wireless communication.
A 50 kW 3D printed fuel cell aimed at clean high power delivery for transportation vehicles.
Hydrogen Fuel Cells are still one of the most effecient and lightest weight in the high power density category.
Using 3D printing methods these large format cells can be easily printed for multiple applications. The highest
cost component is the nafion membrane.
This project uses jquery mobile, php, and mysql to implement a basic image and video sharing
web application.
This project contains a schematic and layout libraries for the AM3358. This can be used for many
applications. The AM3358 has linux and android board support packages available through TI.
This gadget has an OLED Display, Spin wheel input, triple axis magnetic sensors, IR themometer, and
audio driver allowing for audio recordings.
This is an atmel based 100W Back EMF Brushless motor controller.
Uses a Atmel Processor to implement a battery protection circuit for a multicell battery used
in an ebike application.
Multi-cell lithium ion battery protection board. Uses TI's BQ77910A IC for multicell battery protection.
Multi-cell battery protection board for high voltage battery packs. Uses TI's BQ76PL537A IC for
multicell battery protection.This IC is easily cascaded to allow high voltage many cell
lithium ion battery packs.
Uses a telit gprs module to send texts which are input using the spin wheel and OLED display.
This is an atmel based 100W Back EMF Brushless motor controller.
Car tracker with GPRS module allows remote vehicle tracking.
Pedometer with battery charger, ADXL345 accelerometer, and Bi-color OLED display.
Uses a uart driver to drive a piezo transducer at 40kHz. Also has an amplifier fed to the PIC to sense
the returning signal. The PIC is then able to calculate the distance using the flight time.
This page is currently under construction.
Jinn Design Lab develops disruptive technologies in consumer electronics, payment technologies, electric vehicle transportation, and energy production.
Kyle Hagin
Norwood Pryor
-- Designed and implemented hardware and firmware for the communications system between the motor
controller, battery management unit, and the main processor.
-- Developed a battery test plan to meet UN 38.3 specifications and found a viable cell option that
met the design constraints.
-- Built working electric test bikes for demonstration units and presented at Makers Faire.
-- Designed and recommended Bluetooth LE solutions to communicate between the bike and a smart phone.
-- Developed vehicle tracking prototypes that communicate with the OBD 2 port.
-- Designed and proposed a next generation Spot Platform that runs a Java VM bare metal on an
ARM Cortex processor with limited flash and ram.
-- Wrote and implemented test plans for FCC and CE certifications for the Container Monitoring Device.
-- Designed Test Fixtures for manufacturing test of the Container Monitoring Device.
-- Developed an Iridium Satellite GPS tracking device for an underwater robot including designing PCBs,
prototyping, firmware design, and testing.
-- Designed pressure tolerant circuits and performed pressure testing using a cold isostatic press.
-- Designed interface boards for high power DC/DC to convert from the battery to system voltage.
-- Programming low pressure hydrogen fuel cell control systems.
-- Preparing monthly military contract reports.
-- Setting up and completing Apple Works With iPhone certification.
-- FCC and CE product design, testing, and certification for the Technology Connector.
-- Designed the Architecture of an Ardica Enabled heated Jacket with Bluetooth for our customer Hugo Boss.
-- Handle programming of customer requests for firmware enhancements.
-- Programming credit card network firmware including writing new networks and modifying existing ones.
-- Developing new products including designing PCBs, prototyping, firmware design and implementation, and field support.
-- Handling support and modification of older versions of the firmware.
This page is currently under construction.